FAQs for MB SD Connect C4 Star Diagnostic Tool

MB SD connect c4 is good mercedes BENZ cars and trucks diagnostic tool , if you want to know more details for this item , the bellowing FAQs for your reference :

Q: Which tool can diagnose and program for Mercedes Benz BUS body.
A: MB SD STAR C4

Q: Does MB SD C4 support online programming ?
A: Yes, our SD C4 hardware support online programming, but you should have an online account first

Q: After I get MB SD connect c4 activation file, I have no idea how to use it, active by star utilities or by EWA NET?
A: We have video tutorial, please click column “Video” to watch. Important note: make sure enter EPC from “EPC NET EXPLORER ” and find out LAN ID, finally active it.

Q: MB SD C4 has error after click “Select MUX”, Status “No Signal”.
A: Please connect to “Local area connection”, and set IP address: 172.29.127.114, Subnet mask: 255.255.0.0. for the details, please watch the video tutorial by clicking column “Video”.

Q: How to install MB SD connect c4 starfinder?
A: it doesn’t need to install starfinder, directly open “c:\program
files\web_etm\index.html “.

Q: My moveable hard disk of MB SD connect C4 has no display. Does it use USB cable to connect the hard disk and then active?
A: Yes, use USB cable to connect the moveable hard disk and the computer, firstly install “setup.exe”, and then import Mercedes Benz software, the computer configuration should not be too low.

Q: After I connect MB SD C4 to the car, SD C4 has no voltage on the PIN8 OBD cable, but when the ignition key on the second position, the PIN8 cable voltage is 12V. What’s the problem?
A: It suggests you don’t start the car, after the car start, the PIN8 will display voltage value.

Q: Xentrty error reading “Internal error: (3.17)-3.173 you must contact the User Help Desk”
A: Don’t set the file “lic-key-2” as read only.

Q: Why MB SD C4 is unable to connect with the computer; even after I try LAN cable.
A: It needs to set the IP address. How to set the IP address?
Start-Connect to all connections-Local Area Connection-right click “Properties”-Internet Protocol-Use the following IP address, IP address: 172.29.127.114, Subnet mask: 255.255.0.0, finally click “Ok”, we have video tutorial, please click column “Video” to watch or contact our customer service to send you.

Q: Can i use this mb star c4 diagnose Mercedes Benz Trucks, 3335, 1823 and 1413?
A: Yes , it can diagnose these models

Q: When I start DAS, it says that, I am using the developer version. In some menus however the software does not seem to be a developer version.Is it or is it not a developer version? am NOT connected to the internet when diagnosing a car. Only the SD-Box is connected to the notebook via WLAN. Could that be the problem?
A: Have you set the “sdc4” well? Could you please do a self-checking for your device? Then show me the result of the self-checking. Please refer to the following steps of self-checking.
A: Did you have the SD C4 set well? Please follow the next instructions to have a self-test, and then send us the self diagnostic report.

Q: MB SD STAR C4 is unable to self-test?
A: check whether the COM PORT is COM2, if it is, there are four possible reasons: 1) the COM PORT has problem; 2) MB SD C4 and the computer has a poor connection. 3) The cable or SDC4 doesn’t work; 4) SD C4 disconnect with the car.

Q: When I do self-diagnosis for MB, I got error message: 3001 Error.
A: Self-diagnostic has error not suggest MB SD C4 has problem. The aim of self-diagnosis is to check whether SD C4 connect well with the computer and the car, whether the IP address and parameter is set correctly, whether the SD connect c4 and the driver has successful communication. We have video tutorial on how to do self diagnosis for SD C4, please follow it to operate, if you are able to self-diagnostic, it suggests MB SD C4 settings is OK, the connections is OK and it has communication between MB SD c4 and the software. Just go to test the car, if you got any errors, screenshot them and send us to judge where the problem is.

Q:MB SD C4 could read chassis number for Smart 1998, but unable to test ECU after connected with the car.
A: It needs login password when test Smart, we have DAS SMART Calculator (Item No. ss27) to help calculate login password.

Q: Will this MB SD C4 can diagnose ML 270 2005 and A class W169 2007?
A:Yes , it can do it , thanks

Q: I wanted to change the way fuel consumption is calculated in the KIW module. This is done in option 1772 of KIW, only adaptable with the developer version of DAS (see FOTO.JPG). Since when starting I have to agree to the special :dangers” the developer version implements, I thought I would be able to change that value. But there is no modify option available
A: the way of fuel consumption cannot be changed; you are allowed to choose option 1772 of KIW.

More details want to know for mb star c4 , welcome to check www.obdii.shop

Be the first to comment

Leave a Reply

Your email address will not be published.


*