Audi A5 TCU Clone with Launch X431 Pad V and X-Prog3

What is Launch X-PROG 3?

Launch X-PROG 3 is an advanced immobilizer & key programmer, by working together with X-431 series diagnostic scanners (X-431 V, X-431 v+, X-431 PAD V, X-431 PAD VII, etc), it can read/write keys to the vehicle, it can perform immobilizer identification, Remote control matching, Key chip reading & matching, immobilizer password reading and immobilizer component replacement etc.

Look at this images for X-PROG 3 supported brands, supported systems, compatible X431 diagnostic scanners and functions (i.e BMW CAS module clone, BMW 8HP clear ISN, Audi transmission clone, MED17 ECU clone and more…)

Good to know:
– X-PROG 3 in gray color: available online eshop like Obdii.shop;
– X-PROG 3 in red color: available in offline dealership.

Today, we will test one of its core functions ” Audi A5 TCU Clone with Launch X431 Pad V and X431 X-prog3″.

Operate in normal method:
Get security code
Get used transmission security code
Make replacement step
TCM programming
Coding, basic setting…

Why clone?
After replacing the used transmission, perform a TCU CLONE may help you skip all security, programming and coding steps. It will effectively improve work efficiency and save working time.

X-PROG 3 Key Immobilizer & X-431 scanner Pad V will help you to quickly complete the entire operation process with ease.

Enter Immo Prog software:
Tap “Service Function”;

Tap “IMMO Program” to read /write the immo related chips and ECU, to read and write car key chip / EERPM chip / MCU chip / EEPROM & Flash for engine ECU and gearbox ECU.

Connecting the VCI in Wifi mode…

Loading…

 

Please connect the diagnostic connector and the X-Prog3 immobilizer key matching adaptor simultaneously.

 

If there is newest version of programmer to be upgraded, click on “Yes”.

 

Tap “Gearbox”

Information: the current read / write data volume is large. To improve communication stability, use the USB for connection, click on “OK”.

Then perform the [Connect] function first.

 

Tap “DL501 Gen1”.

 

Tap “View Wiring Diagram”.

Please connect the engine to the diagnostic connector according to the picture and power the device on.

Launch Pad V X Prog3 Audi A5 Tcu Clone 08

Connect the pin to the car transmission.

Launch Pad V X Prog3 Audi A5 Tcu Clone 09

Launch Pad V X Prog3 Audi A5 Tcu Clone 10

Launch Pad V X Prog3 Audi A5 Tcu Clone 11

Launch Pad V X Prog3 Audi A5 Tcu Clone 12

Star the Clone process

Click on “Connect”.

Launch Pad V X Prog3 Audi A5 Tcu Clone 13

 

Tap “Backup EEPROM Data”.

Please input the save file name.

Data backup succeeded.

Launch Pad V X Prog3 Audi A5 Tcu Clone 14

Launch Pad V X Prog3 Audi A5 Tcu Clone 15

Tap ” Back up Flash data” and it will reading.

Please input the save file name.

Data backup succeeded.

Launch Pad V X Prog3 Audi A5 Tcu Clone 16

 

Tap “Disconnect” until you can see “Disconnect successfully”.

Launch Pad V X Prog3 Audi A5 Tcu Clone 17

 

Connect the pin of XProg 3 to the transmission need to be replace.

Launch Pad V X Prog3 Audi A5 Tcu Clone 18

Tap “DL501 Gen 1” and then “Connect”.

 

Tap “Restore EEPROM Data”.

Choose the backup file.

And then get information “Data successfully restored”.

Launch Pad V X Prog3 Audi A5 Tcu Clone 19

Launch Pad V X Prog3 Audi A5 Tcu Clone 20

Tap “Restore Flash Data”.

Restoring…

Data successfully Restored!

Launch Pad V X Prog3 Audi A5 Tcu Clone 21

 

Quit the software of Launch X431 PAD V, disconnection succeed.

Do not forget to remove the XPROG 3 VCI from the vehicle.

 

Job is done!

Make a basic setting and the car is ready to drive.

Be the first to comment

Leave a Reply

Your email address will not be published.


*