What is Launch X-PROG 3?
Launch X-PROG 3 is an advanced immobilizer & key programmer, by working together with X-431 series diagnostic scanners (X-431 V, X-431 v+, X-431 PAD V, X-431 PAD VII, etc), it can read/write keys to the vehicle, it can perform immobilizer identification, Remote control matching, Key chip reading & matching, immobilizer password reading and immobilizer component replacement etc.
Look at this images for X-PROG 3 supported brands, supported systems, compatible X431 diagnostic scanners and functions (i.e BMW CAS module clone, BMW 8HP clear ISN, Audi transmission clone, MED17 ECU clone and more…)
Good to know:
– X-PROG 3 in gray color: available online eshop like Obdii.shop;
– X-PROG 3 in red color: available in offline dealership.
Today, we will test one of its core functions ” Audi A5 TCU Clone with Launch X431 Pad V and X431 X-prog3″.
Operate in normal method:
Get security code
Get used transmission security code
Make replacement step
TCM programming
Coding, basic setting…
Why clone?
After replacing the used transmission, perform a TCU CLONE may help you skip all security, programming and coding steps. It will effectively improve work efficiency and save working time.
X-PROG 3 Key Immobilizer & X-431 scanner Pad V will help you to quickly complete the entire operation process with ease.
Enter Immo Prog software:
Tap “Service Function”;
Tap “IMMO Program” to read /write the immo related chips and ECU, to read and write car key chip / EERPM chip / MCU chip / EEPROM & Flash for engine ECU and gearbox ECU.
Connecting the VCI in Wifi mode…
Loading…
Please connect the diagnostic connector and the X-Prog3 immobilizer key matching adaptor simultaneously.
If there is newest version of programmer to be upgraded, click on “Yes”.
Tap “Gearbox”
Information: the current read / write data volume is large. To improve communication stability, use the USB for connection, click on “OK”.
Then perform the [Connect] function first.
Tap “DL501 Gen1”.
Tap “View Wiring Diagram”.
Please connect the engine to the diagnostic connector according to the picture and power the device on.
Launch Pad V X Prog3 Audi A5 Tcu Clone 08
Connect the pin to the car transmission.
Launch Pad V X Prog3 Audi A5 Tcu Clone 09
Launch Pad V X Prog3 Audi A5 Tcu Clone 10
Launch Pad V X Prog3 Audi A5 Tcu Clone 11
Launch Pad V X Prog3 Audi A5 Tcu Clone 12
Star the Clone process
Click on “Connect”.
Launch Pad V X Prog3 Audi A5 Tcu Clone 13
Tap “Backup EEPROM Data”.
Please input the save file name.
Data backup succeeded.
Launch Pad V X Prog3 Audi A5 Tcu Clone 14
Launch Pad V X Prog3 Audi A5 Tcu Clone 15
Tap ” Back up Flash data” and it will reading.
Please input the save file name.
Data backup succeeded.
Launch Pad V X Prog3 Audi A5 Tcu Clone 16
Tap “Disconnect” until you can see “Disconnect successfully”.
Launch Pad V X Prog3 Audi A5 Tcu Clone 17
Connect the pin of XProg 3 to the transmission need to be replace.
Launch Pad V X Prog3 Audi A5 Tcu Clone 18
Tap “DL501 Gen 1” and then “Connect”.
Tap “Restore EEPROM Data”.
Choose the backup file.
And then get information “Data successfully restored”.
Launch Pad V X Prog3 Audi A5 Tcu Clone 19
Launch Pad V X Prog3 Audi A5 Tcu Clone 20
Tap “Restore Flash Data”.
Restoring…
Data successfully Restored!
Launch Pad V X Prog3 Audi A5 Tcu Clone 21
Quit the software of Launch X431 PAD V, disconnection succeed.
Do not forget to remove the XPROG 3 VCI from the vehicle.
Job is done!
Make a basic setting and the car is ready to drive.
Leave a Reply